Service
Plumbing Fixture Installation
Fitting taps, basins, toilets, showers and baths, including the shutoff valves and connectors that decide whether the job stays trouble-free.
- Licensed and insured
- Price agreed before work
- A plumber who works your area
Measure before the old one comes out
The most common way a fixture installation goes wrong is that the new item does not match what is there, and it is entirely preventable.
Taps: the number of holes and the spacing between them.
Sinks and basins: the cutout size and the mounting type, since undermount and drop-in are not interchangeable in both directions.
Toilets: the rough-in, the distance from the finished wall to the centre of the drain, which is not always the standard twelve inches in older houses.
Showers and baths: the valve position and the waste location.
Five minutes with a tape before ordering avoids the situation where the old fixture is out, the water is off, and the new one will not fit.
Two small things while everything is open
An installation is the cheapest possible moment to deal with the parts nobody thinks about.
The shutoff valves. Old ones seize, and a stop that will not close means every future repair on that fixture begins by isolating the whole house. Replacing them with the water already off adds minutes.
The supply connectors. New ones, every time. They have a finite life, and when a braided connector fails it does not drip: it runs at mains pressure into a cabinet, typically while the property is empty.
Neither is exciting and together they remove the two most likely reasons anyone comes back.
Does this sound familiar?
Problems this service solves
- New fixtures going into a renovated bathroom or kitchen
- A fixture that does not match the existing connections
- Shutoff valves that no longer turn
- Old supply connectors that should not be reused
- A fixture position changing within a room
Signs you need plumbing fixture installation
If more than one of these is true, the problem is usually past the point a plunger or a store-bought cleaner will fix.
- The room is being updated or refitted
- The new fixture has different connections to the old
- The shutoff valves under the fixture are seized
- Supply hoses are old or corroded
What to expect
How the visit works
Check the fit before anything is removed
Hole spacing, waste position and rough-in dimensions decide what will physically go in, and they are worth confirming before the old fixture comes out.
Replace seized shutoffs
A valve that will not turn is replaced while the water is already off, so the next repair does not mean isolating the whole property.
Fit new connectors and seals
New flexible connectors and new seals every time. Reused ones are the most common cause of a callback.
Set, seal and test
The fixture is set level and secure, connected, and run under pressure with every joint checked before the job is finished.
What's included
What you get on every job, whoever we send.
- Fit confirmed before the old fixture is removed
- Seized shutoff valves replaced while access is open
- New connectors and seals rather than reused ones
- Everything run and checked under pressure
Questions
Plumbing Fixture Installation questions
Can I buy the fixture myself?
Yes, and plenty of people do. The one thing worth doing before you order is checking the connections against what is there: hole spacing for a tap, waste position for a sink, rough-in distance for a toilet. Those are the dimensions that decide whether something physically fits, and they are not standard across every product. A fixture that nearly fits is the most common reason an installation stalls halfway through.
Why replace the shutoff valves?
Because old compression stops seize, and a shutoff that will not close is worse than useless: it means the next repair on that fixture starts with isolating the entire property. Replacing them while the water is already off and the access is already open takes minutes and very little money. Discovering the problem in three years, during a leak, is a considerably worse moment.
Do the supply hoses really need replacing?
Yes. Braided flexible connectors have a service life and their failure mode is not a drip: the braid corrodes, the inner tube lets go, and an open supply line runs at full pressure into a cabinet, usually while nobody is home. They cost very little, they take minutes, and disconnecting and reusing an old one also disturbs a seal that had settled. New every time is the right default.
Related services
Faucet Installation
Fitting new taps, including the hole configuration, the shutoff valves underneath and the supply connectors that decide whether it stays leak-free.
See what this coversToilet Installation
Fitting a new toilet, including the flange condition and floor level that decide whether it seals properly or rocks and leaks within a year.
See what this coversSink Installation
Fitting kitchen and bathroom sinks, including the cutout, the mounting method and the waste and trap arrangement underneath.
See what this coversWater Heater Repair
Diagnosis and repair of gas, electric and tankless water heaters, including no-hot-water calls, leaks, pilot problems and sediment flushing.
See what this covers
Get it fixed
Plumbing Fixture Installation, handled locally
Call with your ZIP code and what you are seeing. We route you to a licensed plumber in your area who does plumbing fixture installation every week.
- Licensed and insured
- Answered 24/7
- Price before work